Tandberg 8000 MXP User Manual Page 28
- Page / 308
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
TANDBERG 8000 MXP
14
2.3 Monitor Configuration
Monitor configuration
Power up the system by using the power rail in the bottom of the base. Switch the system on by
activating the power switch on the codec (located on the right hand side at the rear of the codec).
A green light is shown (located in the center on the front of the codec). After the system has
performed a self-test routine, the main menu will be displayed on the monitor.
If the system does not start, check the following:
Check that the monitors are receiving power by looking at the right hand side. You should
see a red light. The monitor must have power in order to be switched on by the codec.
Check that the codec has power and is switched on.
If there is still no signal on the monitor, press the 'Digital RGB (2)' button on the plasma
remote control in order to select the 'Digital RGB input (DVI-D)' on the monitor.
Press the ‘Screen Size’ button on the plasma remote control in order to select which view
type is to be used on the monitor.
Recommended view is FULL. This is a 16:9 mode that utilizes the full size of the monitor.
Point the plasma remote control towards the lower right of each monitor (where the IR
sensor is located) in order to switch mode. For the second monitor, this must also be
done for the 'Digital RGB input (DVI-D)' : Press ‘Digital RGB (2)’ to select this input, then
'Screen Size’ until the FULL view is shown.
- User Manual 1
- CAUTION! 2
- Trademarks and Copyright 3
- Environmental Issues 6
- Operator Safety Summary 7
- Contact us 9
- Table of Contents 10
- 1 Introduction 15
- - TANDBERG First 17
- 1.1 At a Glance 18
- 1.2 Menu Structure 22
- 2 Installation 24
- 2.1 Unpacking and Mounting 25
- 2.2 Connecting Cables 27
- 2.3 Monitor Configuration 28
- 2.4 System Configuration 30
- 3 General Use 33
- 3.1 The Welcome Screen 34
- 3.2 Using the Remote Control 35
- ** Ordered separately 38
- 3.2.1 Navigation 39
- 3.2.2 Selfview 40
- 3.2.3 Layout 42
- 3.2.4 Mic Off 43
- 3.2.5 Volume + and 44
- 3.2.7 Touch Tones 46
- 3.3 On-screen Indicators 47
- 3.4 Using the Menu 49
- Control is possible 50
- 3.5 Make a Call 51
- 3.5.1 Place Video Call 52
- 3.5.2 Place Telephone Call 53
- 3.5.3 Add Call 54
- General Use 55
- 3.5.4 Call Settings 56
- 3.5.5 Streaming 57
- 3.6 Answer an incoming call 59
- 3.7 End Call 60
- 3.8 Standby 61
- 3.8.3 Do Not Disturb 64
- 3.9 Phone Book 65
- 3.9.1 Call Log 66
- 3.9.2 My Contacts 67
- 3.9.2.1 Add New Contact 69
- 3.9.2.3 Edit Contact 72
- 3.9.2.4 Delete Contact 73
- 3.9.3 Global Contacts 74
- 3.9.3.1 Up one Level 75
- 3.9.3.2 Search 76
- 3.10 Camera Control 78
- 3.10.1 Move Camera 79
- 3.10.2 Far End Control 80
- 3.10.3 Camera Presets 81
- 3.10.4 TANDBERG Tracker 82
- 3.10.5 Picture Control 83
- 3.10.6 Camera Tracking 84
- 3.11 Presentation 85
- 3.11.1 Presentation Key 86
- 3.11.2 Presentation Menu 87
- 3.11.5 Dual Stream (DuoVideo 90
- /H.239) 90
- 3.11.6 Take New Snapshot 91
- 3.11.7 Display Snapshot 92
- 3.12 Conference Services 93
- 3.12.2 Conference Layout 97
- 3.12.3 Terminal Names 98
- 3.12.4 Chair Control 99
- Participant 100
- 3.12.8 Terminate Meeting 103
- 3.13 Control Panel 106
- 3.13.1 Diagnostics 107
- 3.13.2 System Information 108
- 3.13.3 Channel Status 109
- 3.13.4 Call Status 111
- 3.13.5 System Selftest 112
- Screen Settings 113
- 3.13.8 Warnings 118
- 3.13.9 Text Chat 120
- 3.13.10 Audio Demo 121
- 3.13.12 Restart 123
- 3.13.13 User Guide 124
- 4 Administrator Settings 125
- 4.1 General Settings 126
- 4.1.1 Language 127
- 4.1.2 System Name 128
- 4.1.3 International Name 129
- 4.1.4 Auto Answer 130
- 4.1.5 Phone Book Settings 131
- 4.1.7 Permissions 133
- 4.1.8 Screen Settings 135
- TANDBERG 8000 MXP 140
- 4.1.9 Software Options 141
- 4.2 Menu Settings 143
- 4.2.1 Input Editor Language 144
- 4.2.2 Menu Timeout In Call 145
- 4.2.3 Menu on TV 146
- 4.2.4 Menu on PC 147
- 4.2.5 Balloon Help 148
- 4.2.7 Kiosk Mode Settings 150
- 4.2.8 Startup 153
- 4.2.9 Icons 155
- 4.3 Presentation Settings 156
- 4.3.1 Presentation Start 157
- 4.3.2 H.239 158
- 4.3.3 Startup Video Source 159
- 4.3.4 Presentation Source 160
- 4.3.5 Snapshot Source 161
- 4.3.6 Auto-Display Snapshot 162
- 4.3.7 PIP Appearance 163
- 4.3.8 PIP Placing 164
- 4.3.9 VNC Settings 165
- 4.4 Call Quality 166
- 4.4.1 Video Algorithm 167
- 4.4.2 Audio Algorithm 168
- 4.4.4 Natural Video 170
- 4.4.6 Video Quality 172
- 4.4.6.2 Native Resolutions 173
- 4.4.7 Default Call Settings 175
- 4.5 Audio 178
- 4.5.1 Inputs 179
- 4.5.2 Outputs 183
- 4.5.3 Echo Control 185
- 4.5.4 Stereo Settings 186
- 4.6 Video 190
- 4.6.1 Camera Tracking Mode 191
- 4.6.2 MCU Status Line 192
- 4.6.4 Web Snapshots 194
- 4.6.6 Video Name 197
- 4.7 Security 198
- 4.7.1 Encryption 199
- 4.7.2 Encryption Mode 200
- 4.7.3 Passwords 201
- 4.8 Network 202
- 4.8.1.1 ISDN-BRI Settings 204
- Advanced ISDN Settings 205
- 4.8.1.2 ISDN-PRI Settings 206
- Line Settings 207
- Advanced ISDN-PRI Settings 207
- 4.8.1.5 H.331 Settings 212
- 4.8.2 LAN Settings 213
- 4.8.2.1 IP Settings 214
- DNS Settings 216
- 4.8.2.2 H.323 Settings 217
- Gatekeeper Settings 218
- CallManager Settings 219
- Advanced H.323 Settings 220
- 4.8.2.3 SIP Settings 222
- Authentication 223
- 4.8.2.4 SNMP Settings 225
- 4.8.2.5 IP Services 226
- 4.8.2.6 Quality of Service 227
- 4.8.2.7 IEEE 802.1x 229
- 4.8.3 Network Profiles 230
- 4.8.4 Data Port 231
- 5 Peripheral Equipment 233
- 5.1 Interfaces 234
- 5.1.2 Audio 238
- 5.1.3 Network 240
- 5.1.4 Data port 245
- 5.2 Document Camera 246
- 5.3 DVD / VCR 247
- 5.4 Additional Cameras 248
- 5.5 Additional Microphones 249
- 5.6 The TANDBERG DNAM and 251
- Speakers 251
- TANDBERG 3000 MXP Profile: 253
- 5.7 Stereo Speaker Kit 255
- 5.8 Telephone Add-On 257
- 5.9 Dual Monitor 258
- 5.11 VESA Display Power 260
- Management 260
- 5.12 Digital Monitor Power 261
- Data (EDID) 262
- 6 Appendices 264
- 6.1 Appendix 1 265
- Appendices 267
- 6.2 Appendix 2 268
- 6.3 Appendix 3 271
- 6.4 Appendix 4 272
- 6.5 Appendix 5 274
- IP Password 275
- Services 275
- SNMP Security alert 275
- 6.6 Appendix 6 277
- 6.7 Appendix 7 278
- 6.8 Appendix 8 279
- 6.9 Appendix 9 280
- 6.10 Appendix 10 281
- 6.11 Appendix 11 282
- 6.12 Appendix 12 285
- 6.13 Appendix 13 287
- 6.14 Appendix 14 288
- 6.15 Appendix 15 290
- 6.16 Appendix 16 296
- 6.17 Appendix 17 297
- 7 Glossary 298
- 8 Index 307
© 2020, manymanuals.com. All rights reserved. | 1.139 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals