Tandberg 1700 MXP User Manual Page 115
- Page / 142
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D 13954.01
MAY 2006
115
TANDBERG 1700 MXP
USER GUIDE
H.323 Settings (IV) – Advanced NAT Settings
Control Panel > Network Settings > LAN Settings
Touch tones Snapshot
Camera Presets
The upper part of the menu is explained on
the preceding pages.
CANCEL
Select this icon and press OK
to leave the menu undoing any
changes.
RESTORE DEFAULTS
Select this icon and press OK
to restore the default settings.
SAVE
Select this icon and press
OK to leave the menu putting
changes into effect.
NOTE! The Advanced H.323 Settings only have
effect when supported by your IP infrastructure.
NAT ADDRESS
This must be the external/glo-
bal IP-address to the router with
NAT support. Packets sent to
the router will then be routed to
the system. In the router, the
following ports must be routed
to the system’s IP-address:
Port 1720
Port 5555-5560
Port 2326-2365
Please contact your TANDBERG
representative for further infor-
mation.
RSVP
Auto. Resource Reservation
Protocol enables the systems to
request the optimum amount of
bandwidth for the duration of an
IP videoconference.
Off. Resource Reservation
Protocol is switched off.
H.323 PORTS
Static. When selecting static
H.323 ports for TCP connec-
tions the ports 5555 to 5574
will be used for Q.931 and
H.245 respectively.
Dynamic. The system will al-
locate which ports to use when
opening a TCP connection.
The reason for doing this is
to avoid using the same ports
for subsequent calls as some
firewall consider this as a sign
of attack.
•
•
•
About Network Address Translation (NAT)
NAT, Network Address Translation, is used when a PC
and a videoconferencing system are connected to a router
with NAT support. NAT support in the videoconferencing
system enables proper exchange of audio/video data
when connected to an external videoconferencing system
(when the IP traffic goes through a NAT router). When NAT
is On, the NAT Server Address will be shown in the startup-
menu: My IP Address: 10.0.2.1.
NAT
On. The system will signal the configured
“NAT Address” in place of its own IP-address
within Q.931 and H.245.
Auto. The system will try to determine if the
“NAT Address” or the real IP-address should
be used within signalling. This is done to
make it possible to place calls to endpoints
on the LAN as well as endpoints on the
WAN.
Touch tones Snapshot
Camera Presets
- Software version F5 1
- D13954.01 1
- JUNE 2006 1
- Trademarks and Copyright 2
- D 13954.01 4
- TANDBERG 1700MXP 4
- USER GUIDE 4
- Safety Instructions 6
- Environmental Issues 7
- What’s in this 9
- User Guide? 9
- Call Handling 10
- Video Meeting Features 10
- MultiSite Features 10
- Control Panel 10
- Preparing for Use 13
- Waking Up the System 14
- Basic Menu Navigation Rules 15
- Camera Adjustments 16
- Selfview 18
- Screen Layout 19
- Local PC Display 20
- Sound Matters 21
- Numerical Keypad Features 22
- About Access Codes 25
- Presets 26
- About the Phone Book 27
- System Asks for Access Code? 27
- About this Feature 28
- About Transfer 29
- Consultative Transfer 29
- Unattended Transfer 29
- About MultiSite 30
- Conferences 30
- Adding Calls 30
- About Call Settings 31
- To Alter the Call Settings 31
- Answering an Incoming Call 33
- Basic Phone Book Features 35
- Searching in the Phone Book 36
- Adding a New Contact Manually 37
- About Multisite Contacts* 39
- Features Overview 42
- About Far End Camera Control 43
- About Camera Presets 44
- Using the Far End Preset 44
- Presentation 45
- Snapshots 47
- About Far End Video Sources 48
- Far End Video Options 48
- About Text Chatting 49
- Chatting with the Other Party 49
- Request and Release Floor 52
- Assign Floor 53
- Terminal Names 54
- About Layout 55
- The Layout Options Available 55
- Setting Display Layout 55
- The Remote Control 57
- Control Panel Options 58
- Set a Password 60
- Password Protection 60
- Clear an Existing Password 60
- Pyccкий, Suomi, Chinese 61
- Language 62
- System Name Settings 63
- Autoanswer 64
- Phone Book Settings 65
- External Services 66
- Permissions 67
- Access Codes 68
- Screen Settings 69
- Software Options 70
- Date and Time Settings 71
- Kiosk Mode Settings 73
- Startup Settings 74
- Call Video Source 78
- Presentation Source 79
- Snapshot Source 80
- Auto-Display Snapshot 81
- PIP Placing 82
- VNC Settings 83
- PC SoftPresenter and VNC 84
- Video Algorithm 86
- Audio Algorithm 87
- Natural Video 89
- Maximum Upstream Rate (kbps) 90
- Video Quality 91
- Default Video Call Settings 94
- Default Net Settings 95
- Default Bandwidth Settings 96
- Level Settings 98
- Alert Tones & Volumes 99
- Graphical View of Settings 100
- MCU Status Line 102
- Floor to Full Screen 103
- Web Snapshot 104
- MultiSite Picture Mode 105
- Video Name 106
- Encryption 108
- IP Settings (I) 110
- IP Settings (II) 111
- H.323 Settings (I) 112
- Touch tones Snapshot 115
- Camera Presets 115
- SIP Settings (I) 116
- SIP Settings (II) 117
- Wireless LAN Settings 118
- SNMP Settings 119
- IP Services 120
- IEEE802.1x 126
- Network Proles 127
- Data Port 128
- The Default Settings 129
- Restore Default Settings (II) 130
- System Information 134
- Call Status 135
- Detailed Call Status 136
- System Selftest 137
- View Adminstrator Settings 138
- IP Address Conict Check 139
- Warnings 140
- Audio Demo 141
Related products and manuals for Monitors Tandberg 1700 MXP
Monitors Tandberg S3 User Manual
(127 pages)
(127 pages)
Monitors Tandberg 6000 MXP User Manual
(287 pages)
(287 pages)
Monitors Tandberg 6000 User Manual
(1 pages)
(1 pages)
Monitors Tandberg 3.0 User Manual
(66 pages)
(66 pages)
© 2020, manymanuals.com. All rights reserved. | 1.264 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals