Tandberg 1700 MXP User Manual Page 19
- Page / 142
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D 13954.01
JUNE 2006
19
TANDBERG 1700 MXP
USER GUIDE
About Screen Layout
The layout of the screen can either be
shown as Picture In Picture (PIP) or Picture
Outside Picture (POP) when displaying more
than one video image. For widescreen moni-
tors, POP is recommended. The behavior
of the Layout key depends on the Picture
Layout setting in Control Panel > Screen
Settings.
Screen Layout
Touch tones Snapshot
Camera Presets
Touch tones Snapshot
Camera Presets
Touch tones Snapshot
Camera Presets
Touch tones Snapshot
Camera Presets
Note! Depending on the number of partici-
pants in your video meeting and whether you
use a dual video stream or not, some of the
locations of the screen layouts may be empty.
The actual positioning of each picture as you
press the Layout key, may vary from the above
examples.
Full screen
Side-by-Side (1+1)
1+21+3
Getting Acquainted with the System
Picture in Picture
When Picture Layout is set to PIP, the Layout
key makes it possible to see a second image
in a smaller view in one of the corners of the
screen. The second image will be placed on
top of the main image. You are free to choose
in which corner the second image is to be
displayed.
Picture outside Picture
When Picture Layout is set to POP, the Layout
key makes it possible to see up to three images
in a composition optimized for wide screens.
The second image can be displayed either as
a side-by-side the main image (1+1) or smaller
images next to the main image (1+2 and 1+3).
Press the Layout button once to get side-
by-side view (1+1). Press again to get the
layouts 1+2 and 1+3, and finally go back
to full screen view. You can also go back to
full screen directly by pressing and holding
Layout for 1 second.
Auto Layout
The system will automatically choose the
best layout for your call. You can, however,
always change layout manually with the
Layout key. Auto Layout applies when you
open or close a dual video stream, or add
or disconnect participants.
Auto Layout also includes automatic PIP.
That implies that PIP will be shown when
suitable, e.g. to display selfview when you
move your near end camera. The automatic
PIP times out after a couple of seconds.
OFF means no automatic layout changes
during a call – you must manually control
the images with the Layout key. Auto Layout
is default ON. To turn Auto Layout OFF, go
to Control Panel > Screen Settings.
Using the Remote Control to Determine the Screen Layout
Picture-outside-Picture
Picture-in-Picture
- Software version F5 1
- D13954.01 1
- JUNE 2006 1
- Trademarks and Copyright 2
- D 13954.01 4
- TANDBERG 1700MXP 4
- USER GUIDE 4
- Safety Instructions 6
- Environmental Issues 7
- What’s in this 9
- User Guide? 9
- Call Handling 10
- Video Meeting Features 10
- MultiSite Features 10
- Control Panel 10
- Preparing for Use 13
- Waking Up the System 14
- Basic Menu Navigation Rules 15
- Camera Adjustments 16
- Selfview 18
- Screen Layout 19
- Local PC Display 20
- Sound Matters 21
- Numerical Keypad Features 22
- About Access Codes 25
- Presets 26
- About the Phone Book 27
- System Asks for Access Code? 27
- About this Feature 28
- About Transfer 29
- Consultative Transfer 29
- Unattended Transfer 29
- About MultiSite 30
- Conferences 30
- Adding Calls 30
- About Call Settings 31
- To Alter the Call Settings 31
- Answering an Incoming Call 33
- Basic Phone Book Features 35
- Searching in the Phone Book 36
- Adding a New Contact Manually 37
- About Multisite Contacts* 39
- Features Overview 42
- About Far End Camera Control 43
- About Camera Presets 44
- Using the Far End Preset 44
- Presentation 45
- Snapshots 47
- About Far End Video Sources 48
- Far End Video Options 48
- About Text Chatting 49
- Chatting with the Other Party 49
- Request and Release Floor 52
- Assign Floor 53
- Terminal Names 54
- About Layout 55
- The Layout Options Available 55
- Setting Display Layout 55
- The Remote Control 57
- Control Panel Options 58
- Set a Password 60
- Password Protection 60
- Clear an Existing Password 60
- Pyccкий, Suomi, Chinese 61
- Language 62
- System Name Settings 63
- Autoanswer 64
- Phone Book Settings 65
- External Services 66
- Permissions 67
- Access Codes 68
- Screen Settings 69
- Software Options 70
- Date and Time Settings 71
- Kiosk Mode Settings 73
- Startup Settings 74
- Call Video Source 78
- Presentation Source 79
- Snapshot Source 80
- Auto-Display Snapshot 81
- PIP Placing 82
- VNC Settings 83
- PC SoftPresenter and VNC 84
- Video Algorithm 86
- Audio Algorithm 87
- Natural Video 89
- Maximum Upstream Rate (kbps) 90
- Video Quality 91
- Default Video Call Settings 94
- Default Net Settings 95
- Default Bandwidth Settings 96
- Level Settings 98
- Alert Tones & Volumes 99
- Graphical View of Settings 100
- MCU Status Line 102
- Floor to Full Screen 103
- Web Snapshot 104
- MultiSite Picture Mode 105
- Video Name 106
- Encryption 108
- IP Settings (I) 110
- IP Settings (II) 111
- H.323 Settings (I) 112
- Touch tones Snapshot 115
- Camera Presets 115
- SIP Settings (I) 116
- SIP Settings (II) 117
- Wireless LAN Settings 118
- SNMP Settings 119
- IP Services 120
- IEEE802.1x 126
- Network Proles 127
- Data Port 128
- The Default Settings 129
- Restore Default Settings (II) 130
- System Information 134
- Call Status 135
- Detailed Call Status 136
- System Selftest 137
- View Adminstrator Settings 138
- IP Address Conict Check 139
- Warnings 140
- Audio Demo 141
Related products and manuals for Monitors Tandberg 1700 MXP
Monitors Tandberg S3 User Manual
(127 pages)
(127 pages)
Monitors Tandberg 6000 MXP User Manual
(287 pages)
(287 pages)
Monitors Tandberg 6000 User Manual
(1 pages)
(1 pages)
Monitors Tandberg 3.0 User Manual
(66 pages)
(66 pages)
© 2020, manymanuals.com. All rights reserved. | 1.365 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals